Home > Whirlpool Duet > Whirlpool Duet Washer Error Codes

Whirlpool Duet Washer Error Codes

Contents

Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen. Unplug washer or disconnect power. 3. You would need to rule out the water valve..By changing water temps...Then check the pump for any blockage..(socks Etc.)...If all checks ok then most likely your pressure water pressure switch is http://bashprofile.net/whirlpool-duet/whirlpool-duet-washer-won-39-t-drain.html

Replace CCU board. Whirlpool Duet Dryer Error Codes Whirlpool Duet Dryer Error Codes. Check Pressure Switch for correct working with a DVM/VOM. 3. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4

Whirlpool Duet Washer Error Codes

Bitte versuche es später erneut. First thing he did was look for baby socks and other small articles of clothing at the pump. Exchange the complete valve block if the steamer valve has not a resistance of approx. 812 Ω between both contacts. 6.

  1. Verify CCU operation by running a Diagnostic Test or any cycle.
  2. Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the MCU Check the Drive Motor
  3. Canceled the cycle, and took about 10 minutes to drain what little water there was in it.
  4. The washer will lock up immediately if the tube is conneceted, even before you can start the diagnostics test and you will have to start all over againg from cycling power
  5. Verify CCU operation by running a Diagnostic Test or any cycle. 6.
  6. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the

Check for continuity of the User Interface harness. 2. Press PAUSE/CANCEL twice to clear the display. Plug in washer or reconnect power. 5. Whirlpool Duet Reset I hope this helps someone with similar issues.

Audible clicks will be heard if the pressure switch contacts are not stuck. The pressure switch is part number W10271610 priced at $34.52. Whirlpool Duet F11 Error Code F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. Check drain pump. 7. http://www.fixya.com/support/t561418-whirlpool_duet_error_code_f_32 If "Sud" is displayed a potential suds lock is detected.

How to Troubleshoot a Whirlpool Cabrio Washer The Whirlpool Cabrio brand high efficiency washer helps homeowners save on energy and water costs as compared to older washers while cleaning... Whirlpool Duet E1 F8 Either the hose leading to the pressure switch is blocked or leaking or the pressure switch is broken You need either to call for service due to warranty or... Exchange steamer electronic board. Make sure all grounding switches are engaged. 3.

Whirlpool Duet F11 Error Code

NOTE: Detects by weight. http://appliancejunk.com/forums/index.php?topic=8686.0 Very unlikely this is the culprit, but its a possibility. Whirlpool Duet Washer Error Codes Disconnect the washer from the power outlet and run a diagnostic test on the washer, the process for this is different depending on your washer but my whirlpool instructions where on Whirlpool Duet Washer Error Code F20 Unplug washer or disconnect power. 2.

Replace CCU board. http://bashprofile.net/whirlpool-duet/whirlpool-duet-washer-error-code-f11.html Do a Duet Washer Quick Test and check for motor function. Check Pressure Switch harness for continuity. 2. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1. Whirlpool Washer Error Code F02

Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). Unplug washer or disconnect power. 2. An F-24 Error Code on a Whirlpool Washer Look for "F24" to appear on the washer LCD screen. have a peek here Unplug washer or disconnect power. 2.

Check the water temperature sensor and connection to it. 3. What Does Sud Mean On A Whirlpool Duet Washer Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU). Check resistance of heating element, if present on this model. (abnormal = infinity) 4.

press cancel if this is the case and start again.

Reason: to make clearer. #5 (permalink) 06-01-2008, 03:27 PM Flo Junior Member Join Date: Jun 2008 Posts: 3 Whirlpool Duet Washer Door/Error F21 Mines was having a simular cannot find it. Im no expert just a guy that can read instructions and likes to play with electrical and mechanical gadgets. What Does F20 Mean On A Whirlpool Duet Plug in washer or reconnect power. 5.

Pull the tube off and blow down it in order to clear any lint in the tube. I have no idea how is got past the tub. order part here It is number 20.This will also indicate how to fix it OK just came back from whirlpool. Check This Out ft.

During the Cleaning Cycle was load detected inside the drum and Cleaning Cycle was interrupted by indicating “rL” to User. It will unlock the door. Like ApplianceAssistant on Facebook! Same problem only we just had machine delivered today.

F32 followed by suds means the pressure switch is bad. How do I go about taking those off to get to the lint catcher? Unplug washer or disconnect power. 2. Remove the washer to and do a Duet Washer Quick Diagnostic Test step C02 should move the dispenser linkage so you can see what's the hang-up.

For those reasons, I was skeptical that the problem was the switch but when i installed the new one and ran through the diagnostic routine....shazaaaam....no more error codes!So even if you In normal use (a little blockage is normal) the steamer cleans itself. Check the water temperature sensor and connection to it. 3. My washer had this same error code.

Plug in washer or reconnect power. 5. This is bad... By removing the hose and tapping on the pressure switch can possibly cause the contact to break free from being stuck. If that doesn't fix it then it could be the control box( the bigger rectangular box in the front right that the wires connect to.) Good Luck and Happy Washing!

The Greens in Alaska We had this same problem. It should be noted that I tested the pressure switch line (all clear) and also pushed a little air through the pressure switch itself and it made the clicking noise it Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the Drive Motor Check the MCU He stated that there is a "break in period of about 3 months and that a pressure switch can get kinda delicate." He also noticed that I have the Watts Floodsafe

If all that looks good check the drain system for blockages or you may have a bad drain pump. Was working fine and now when I press start, I get the code "FL"and then "d" flashing. rL Load Detected W/Clean Cycle Error A load of clothes was detected during a Clean Washer cycle.