Home > Whirlpool Duet > Whirlpool Duet Washer Error Code F11

Whirlpool Duet Washer Error Code F11

Contents

Flashing display time Open lid If the lid opens while the unit is in running mode, time remaining will flash in the display. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). To replace the control board, you have the option of calling a technician, which can, depending on where you're from, cost you around 400 USD. With this failure, power to the motor controller cannot be turned off by the machine controller. Source

I can clear the code and when I try to run a new cycle and press the start button, I hear a little noise (like it always does before starting the The puzzling part of this all is the F-01 that suggests the CCU is not working, it is a new and tested CCU. Recall Alerts Careers PartSelect Canada Free Repair Help Appliance Repair Instant Repairman Dishwasher Dryer Microwave Range / Stove / Oven Refrigerator Washing Machine Helpful Resources PartSelect Community Twitter Facebook Page YouTube See Details More Products Whirlpool WFW90HEFW 4.5 cu. http://www.applianceblog.com/mainforums/threads/21250-Whirlpool-duet-has-f-01-error-code

Whirlpool Duet Washer Error Code F11

It will try to lock it 6 times before displaying the error. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. After you have recorded any stored errors you can clear the code by pressing and holding the 3rd diagnostics button for 5 seconds. If there is an error reading this data it will cause this error.

Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle. "SL" is displayed if suds are detected but the F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). Whirlpool Duet F11 Error Code Troubleshooting Fault Codes Fault Codes Admiral Bosch Dacor Estate Frigidaire GE Gibson Hotpoint Jenn Air Kelvinator Kitchen Aid Magic Chef Maytag Roper Sears / Kenmore Tappan Thermador Whirlpool We are Safe, Secure,

Press 'Stop/Cancel' to clear display. Replace failed component. ^ top F15 Motor Control Unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. If you could blow through the hose easily, or you succesfully removed whatever was blocking the hose, reconnect the hose and turn the machine back on. http://applianceassistant.com/Washer-Repair/Duet/Duet-Washer-Error-Codes.php Wow.

With an overfill condition, the beeper repeats a warning every 10 seconds with no time out. Whirlpool Duet Washer Reset Wird geladen... Irvington, NY "I LOVE seeing customer service excellence, seeing follow through on promises." Gregory R. Is the drain hose too far down the drain pipe?

  • Check that the tab on the washer's door that inserts into the door lock is not broken, that it's properly aligned with the door lock hole, and that there is nothing
  • Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
  • This is the most common Duet washer error code!
  • F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.
  • There is one more thing you need to check before you order that part.
  • If connections are ok, then check individual switches as outlined for the F5 error code.

Whirlpool Duet Washer Error Code F01

Like it never happened : )Duet Washer Part Descriptions Back to Top Back to Top You May Also Like... anchor Replace sensor if found defective. Whirlpool Duet Washer Error Code F11 Potential Causes • A power glitch may cause this error. Whirlpool Duet Washing Machine Error Codes Measure door switch (door open = switch open small low voltage terminals).

If code re-appears, replace control board (also called ERC or clock). this contact form The washer is just over one year old. Mesquite, TX "When you say 'Fast Shipping', you aren't kidding!" Warnie M. Press and hold any key for 1 minute to clear R failure code from memory. Whirlpool Duet Error Code E01

Sud SUDS LOCK (Overdose of detergent detected during the wash cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. I cannot clear this code and the washer stopped operating in the middle of a cycle. Check wire harness connections to the Central Control Unit (CCU) and the dispenser motor. http://bashprofile.net/whirlpool-duet/whirlpool-duet-washer-error-code-f1.html F1 Board failure Replace control board (also called ERC or clock).

Not to ignore your instruction, but when I cleaned it out the first try, I literally laid on the floor and put my shop vacum nozzle inside the pump and let Whirlpool Duet E01 F01 F9 - Oven Door Lock Failure - Check door lock switches and wiring. Wird geladen...

Is there a part I can replace so that my wash cycle operates properly?

F8 Board failure Replace control board (also called ERC or clock). Sr - Stuck Relay - The machine control board may have a bad relay and may need to be replaced. Your Duet washer has detected a load during a washer cleaning cycle. Whirlpool F01 Code Its going to take me a while to get through it.

Check drain pump and pressure switch and verify CCU operation by running a diagnostic test or any cycle. You press both buttons at the same time and hold for 5 seconds. A large number of people are experiencing the F1 error code and according to some sources, this could be due to a faulty design on Whirlpool's control board. Check This Out Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4.

You may have to register before you can post: click the register link above to proceed. Ld Long drain "Ld" flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets. See Details Whirlpool WFW92HEFC 4.5 cu. If you prefer video instructions on replacing the control board, here they are: If you managed to remove the Whirlpool F1 error code from your machine, please post your experience and

Opening the lid will allow you to view and redistribute the load. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). Be prepared, a lot of water is going to come out when you open that filter.Click to enlarge. Ask Your Own Appliance Question Customer: replied5 years ago. Disconnect power and unplug the unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU).

F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC Wähle deine Sprache aus. Melde dich an, um unangemessene Inhalte zu melden. All F5-E Codes - Door Switch Defect - This occurs when the door switches do not match.

Replace switch if defective. 5.