Verify CCU operation by running a Diagnostic Test or any cycle. F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), Replace MCU board. Whirlpool Clothes Washer Error Code F32 The pressure switch is a necessity when using a Whirlpool washer.
Whirlpool Duet Sport Dryer F 01 Error Code
Plug in washer or reconnect power. 4. Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the Drive Motor Check the MCU NOTE: Detects by weight. If a failure occurs during high-speed spin, the door unlocks after 3 minutes. 1.
rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum.
Check if the hose is not blocked.
Check the Water Temperature Sensor, Heating Element and Element Relay Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect
Check for continuity of the User Interface harness. 2.
If the above does not correct the problem, go to step 7. 7.
The relay might be soldered or always open.
If failure occurs during high-speed spin the door unlocks after 3 minutes. 1.
An open circuit would indicate a bad pump.
You can try selecting a drain/spin cycle and see if the pump tries to run.
Check door switch contacts. 4. Check the drain pump filter for foreign objects. 5. Unplug washer or disconnect power. 3. Whirlpool Duet Error Code F33 Replace the pump.
Hi again, Whirlpool's F21 decodes as 'control unit failure' which definitely means a service call and is probably tied in with the F33. Top-Load ... I attached a diagram with what contact points you can use the test the pressure switch at different water levels. http://www.justanswer.com/appliance/5pb62-whirlpool-duet-sport-showing-code-f33.html Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse,
NOTE: The door switch/lock unit can be manually unlocked. Whirlpool Duet Sport Drain Pump Forum New Posts FAQ Calendar Community Member List Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Store Blog Advanced Search Forum Appliance Repair Help Washer Repair whirlpool F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle. Verify Drain pump operation 2.
F21 Error Code Whirlpool Duet Sport
Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. http://www.shopyourway.com/questions/1079071 Unplug the unit to service. Whirlpool Duet Sport Dryer F 01 Error Code Press PAUSE/CANCEL twice to clear the display. 5d Error Code Whirlpool Duet Sport Check the drive system for any worn or failed components. 5.
F11 MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions. F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. The failure will reset after running the Diagnostic Test Program. 1. http://bashprofile.net/whirlpool-duet/whirlpool-duet-sport-washer-code-f-33.html Push the door and check if it is completely closed. 2.
Drying, 10/14/2016 10/14/2016 JACUSTOMER-x0uwnnmp- Whirlpool refrigerator model GX5SHDXVQ02. Whirlpool W10130913 This entry was posted in Washer Repair on April 27, 2013 by Samurai Appliance Repair Man. Check the electrical connections at the pump and make sure the pump is running.
Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5.
The resistance of both door coils (between pin 1 and 3) should be approx. 320 Ω. Whirlpool Duet Error Code F33; How to Find a... Please help, I am trying to spend less than if I were to buy a new washer. Whirlpool Duet Won't Drain Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2.
Make sure all grounding switches are engaged. 3. Check the water temperature sensor and connection to it. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Unplug washer or disconnect power. 2.