Home > Whirlpool Duet > What Does Fh Mean On A Whirlpool Washer

What Does Fh Mean On A Whirlpool Washer

Contents

I don't have a multimeter to test. This is exactly what my Duet washer is doing. I tried to ensure it was properly connected, but when I pulled the connector plug, a little circuit board came out with some sort of sensor on it. Are you using flood-preventing devices that can shut off the water to the washer? check over here

Top 5 Reasons Top-Load Washer Is Making Loud Noise? Nächstes Video Whirlpool Washing Machine Error Codes Diagnosis - Dauer: 5:50 eSpares 22.240 Aufrufe 5:50 Kenmore HE4T (FH) Repair Code DIY - Dauer: 10:25 allritythen 14.039 Aufrufe 10:25 kenmore front load The FH code in the owners manual only talks of a water supply problem, and my washer fills with water before giving the code. If this happens the water inlet valve or the water level pressure switch may be defective. http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/400-5-620619-/Whirlpool-F-H-FH-No-Water-Entering-Machine-or-Pressure-Switch-Failure-

What Does Fh Mean On A Whirlpool Washer

I ran the diagnostic test, and at Step C:01 (tests flowmeter and cold water inlet valve), the test displayed code FH. It took a while to figure this out because the diagnostic test did not bring up any error so I thought the black tube was fine but I was wrong. All rights reserved.

  • To start viewing messages, select the forum that you want to visit from the selection below.
  • I've been doing that.
  • Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help

here is what i have run across on at least 3 occasions; the w/l switch tubing(air tube) is supported by a small retainer that establishes the tubes routing toward the side Top 3 Reasons Top-Load Washer Won’t Drain? I will replace the flowmeter and hope for the best. Fh Error Code Maytag Washer Did you clean the screen in the cold water fill valve?

Then, consider replacing the flow meter. Whirlpool Duet Flow Meter You already have blown out hose and it's clear. click Here to view this post Posted: Thu Nov 17th, 2005 08:58 pm 12th Post HAMMER Lurking at the Threshold Joined: Location: Posts: Flavorite Brew: Status: Offline FOR CODE http://www.doityourself.com/forum/electric-large-kitchen-home-appliances/507952-stumped-error-code-fh-whirlpool-duet-front-load-washer.html This is an emergency shut down to prevent the washer from overfilling when it reaches 10.5 gallons of water (per manual).

Thanks for the update too. 04-06-15,02:26 PM #12 DrMoisheP Member Join Date Apr 2015 State Non-US Posts 1 The flow meter has a spinner with a magnet (in which particles could Whirlpool Duet Pressure Switch I have checked the water inlet hoses and the inlet filters, and they seem to be OK (maybe a little debris on the cold water inlet filter, which I cleaned off). It's free! Back To Top Posted: Mon Nov 7th, 2005 02:41 pm 11th Post kdog Fellow, Academy of Sublime Masters of Appliantology Joined:Sun May 8th, 2005 Location:Calgary, Alberta Canada Posts:2560

Whirlpool Duet Flow Meter

Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the http://producthelp.whirlpool.com/Laundry/Washers/Washer_Product_Assistance/What_is_an_F20_or_FH_Error_Code_on_my_Front-load_Washer I searched everywhere on the internet for the fix and finally found it. What Does Fh Mean On A Whirlpool Washer It had a comb, a key, several paper clips, a pair of (disintegrated) reading glasses, several bolts and screws, and 65 cents in change, among the identifiable stuff. Ghw9150p Errorcodes Does anyone know how to check the flowmeter, which is one of the things recommended to check for the FH error code?

I took the flowmeter off and blew through it. http://bashprofile.net/whirlpool-duet/whirlpool-duet-washer-won-39-t-drain.html No--I replaced that and get the exact same symptoms. Thank you for posting! Logged Haroldsappliance.com domain Technician Member Since: Nov 2012 Posts: 2535 Country: Re: Whirlpool Duet Washer HF error code « Reply #7 on: March 18, 2013, 09:14:13 PM » I figured the Whirlpool Duet Washer Flashing F And H

Then, consider replacing the flow meter. All rights reserved. Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. this content Live Chat 1-800-269-2609| En Español| Available 7 days a week RepairClinic.com Logo Fast Shipping My Orders Login Order History My Model Numbers Cart(0) What is a model number, and where

This has fixed my problem perfectly and have no more errors. Whirlpool Duet Diagnostic Mode If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. I now have both an overpriced spare water inlet valve and flowmeter that the parts store won't take back.

The time now is 09:38 AM.

Back To Top Posted: Sat Aug 20th, 2005 05:34 pm 2nd Post Pegi Fellow, Academy of Sublime Masters of Appliantology Joined:Tue May 3rd, 2005 Location:Wichita Falls, Texas Finally fixed mine and it was the little black tubing going to the pressure switch. Circle Parts Dr On Google+ "Like" Parts Dr on Facebook Follow Parts Dr on Twitter Reply With Quote Quick Navigation Washer Repair Top Site Areas Settings Private Messages Subscriptions Who's Online Whirlpool Duet Washer Error Code F20 Contact Us DoItYourself.com Mobile Site Privacy Statement Top All times are GMT -7.

This code can also display if the machine is filling with water, the flow meter measures 10.5 gallons of water into the machine, but the water level pressure switch does not Lesson learned: Don't rule out the CCU just because the self-diagnostic test doesn't flag it. All other trademarks are owned by their respective companies.MSRP is Manufacturer's Suggested Retail Price and may not necessarily be the price at which the product is sold in the consumer's area. have a peek at these guys I ended up purchasing a new black tube for something like $3.00 at an appliance repair supply shop.

Is the unit draining completely ? Any ideas as to what might be going on? Ifthe error remains on the display,andall of the other conditions above have been checked,call for service. Are both the hot and cold water faucets turned on?

How do I get the door open? thanks __________________ - #6 (permalink) 01-08-2009, 05:31 AM kayakcrzy Senior Expert APP Volunteer Join Date: Feb 2008 Location: Missouri Posts: 2,429 Pull the wires off the pump, and I realize now how easy it is to clean that out and will do it regularly in the future. That is a big problem with that washer.

Thank you for your support. Ask stef Your Own Question stef, Home Appliance Technician Category: Appliance Satisfied Customers: 117 Experience: 15 years experience specialising in fixing what others can't. Kategorie Praktische Tipps & Styling Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen...