Home > Whirlpool Duet > Fh Error Code On Whirlpool Duet Washer

Fh Error Code On Whirlpool Duet Washer

Contents

Hi again, Whirlpool's F21 decodes as 'control unit failure' which definitely means a service call and is probably tied in with the F33. Possible Causes/Procedure 1. Whirlpool Duet Washer... Any suggestions? have a peek at this web-site

by Fred M Earned 93,433 community points in Click'>Washers May 29th, 2010 Answered in 19 hours Comment Give your feedback by voting on answers 0 votes Didn't find what you are Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Open and close the door. 2. Check the drive motor for powered rotations. 8.

Fh Error Code On Whirlpool Duet Washer

If the impeller isdetached from the shaft, is broken or has any scratch, the drain pump mustbe replaced.- Plug in washer or reconnect power.- Verify the unit operation by running a F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). MAIN RELAYS ERROR One of the main relays is not working properly.

  • Check the MCU by looking for operations of the drive motor. 7.
  • Check the electrical connections at the pump and make sure the pump is running.
  • Check Door Lock/Switch Assembly for foreign objects Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure Duet Sport Washer Failure Code Condition
  • How to Connect a Whirlpool Duet Washer.
  • Make sure that both valves at the water source(s) are turned on all the way. 2.
  • Check the drive system for any worn or failed components. 4.
  • They use the status lights on the touchpad/LED.
  • By Model Number By Part Description By Part Number powered by AppliancePartsPros.com « Whirpool Ultimate Care II won't drain or spin (lid switch good) | mayatg brovos top load hce
  • Wird geladen...

Unplug washer or disconnect power for two minutes. Check/clean drain pump filter of foreign objects. 5. Also inside was access to the drain filter. F09 Error Code Whirlpool Duet Washer F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times.

Login|Contact Us Appliance Need Appliance Repair Help? I am getting a f33 error code. Unplug washer or disconnect power. 3. see this These are the parts for your model washer: Water Level Pressure Switch - W10514214 Flowmeter - W10110225 Attached Thumbnails Ryan www.PartsDr.com - Discount Appliance Parts & Accessories Please help keep

You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. F11 Error Code On Whirlpool Duet Washer Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Short circuit of Heater to Ground. Push the door and check if it is completely closed. 2.

F35 Error Code On Whirlpool Duet Washer

All times are GMT -5. look at this site Whirlpool Duet: Error Code F5 Whirlpool Duet Error Code F33. Fh Error Code On Whirlpool Duet Washer If resistance is 0 Ω or infi nite value, replace NTC. 4. F21 Error Code On Whirlpool Duet Washer Check mechanical linkage from dispenser motor to the top of the dispenser.

Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). http://bashprofile.net/whirlpool-duet/whirlpool-duet-washer-error-code-f02.html Check door switch contacts. 4. Check the wire harness connections to the Motor Control Unit, Central Control Unit, and Interference Filter. 3. Restart a load of laundry and make sure the error message disappears. F25 Error Code Whirlpool Duet Washer

Check the drain pump filter for foreign objects. 5. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the well these are complicated machines and to be honest I don't want to tell you to just start replacing parts that could cost you more in the long run. http://bashprofile.net/whirlpool-duet/whirlpool-duet-washer-error-code-f1.html Replace MCU board.

Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5. F28 Error Code Whirlpool Duet Washer Replace MCU board. Check the pressure switch. 8.

Check connections of the CCU board within the housing.

Unplug washer or disconnect power. 2. Sorry ;-0( Good luck, John ... How to Program a Whirlpool Duet Washer. Whirlpool Duet Sport Drain Pump The parts should be working fine; it is just the connection that caused the ...

Kenmore Elite Oasis... Check wire harness connections to the pump and Central Control Unit (CCU). 3. Check harness on steamer electronic board. 2. have a peek here Melde dich an, um dieses Video zur Playlist "Sp├Ąter ansehen" hinzuzuf├╝gen.

It will try to unlock the door 6 times before displaying the error. Replace Central Control Unit if drum is not moving. The time now is 04:16 AM. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) Check/Clean Drain Pump Filter of foreign objects Check Drain Pump Check Pressure Switch Check CCU F/dL

Check that the serial harness at the MCU is not mounted upside down. Prevention/Solution Stop the current washing cycle, drain the remaining water and remove any clothes left in the washer. Replace the pump.