Home > Whirlpool Duet > F02 Error Code On Whirlpool Duet Washer

F02 Error Code On Whirlpool Duet Washer

Contents

As a preventative measure!! Any thoughts from a visitors standpoint on that? F/05 Water Temperature Sensor Error If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, THERE IS A LOT OF WATER. have a peek at this web-site

This means that the dispenser motor which directs fill water to the appropriate dispenser area, is not moving properly. Nope. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). Check water valve electrical connections before changing out the valve.

F02 Error Code On Whirlpool Duet Washer

Took about an hour to resolve due to the small space and wet rug... Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Your Duet washer has detected a load during a washer cleaning cycle.

Caught about half the water in the cookie sheet. The best way I have found to deal with the water when your washer's drain pump isn't working is to use a shop vac and pull from the drain hose. You will see the heating element and will be able to see if all of the debris was removed. Whirlpool Duet Error Code F01 Ugly is the new Sexy!

Had 2 socks and 2 acorns in mine. 04/16/2012 by Robert Dixon Thank you very much! Whirlpool Duet Drain Pump Clearing this area may resolve your problem. It also means unplug the washer so you don't get electrocuted! http://www.appliancerepairlesson.com/2011/03/12/how-to-fix-whirlpool-duet-error-code-f02-duet-sport-error-f02-fix/ This little hose goes from the sensor to a small reservoir behind the tub, it was completely clogged so the sensor never had a good reading about the water level in

Finally it started throwing the F02 codes at me at 11 pm. F02 Error Whirlpool Duet Dryer I can't believe they don't have that in the manual. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? There is still a lot of extra water that comes out when you open the drain plug but it mopped up fine.

  • Replacement worked great.
  • There was a small sock in the coin trap, once I removed it the washer is like new......Thanks 12/25/2014 by Ken Thanks for the help!
  • Easy peasy..thank you so much..save us a service call.
  • But don't worry: you already unplugged the power cord, right?) Unscrew the trap cover a little (Don't remove it completely!) and let the water out.

Whirlpool Duet Drain Pump

Voila! Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the F02 Error Code On Whirlpool Duet Washer By Model Number By Part Description By Part Number powered by AppliancePartsPros.com #2 (permalink) 05-16-2010, 07:46 PM anonymous Junior Member Join Date: May 2010 Posts: 1 pressure Whirlpool Duet Drain Pump Filter I know the sensor switch is working because it switches with other steps except when it detects the sud.

Put all back together and again and was working fine except kinda made a rattling noise and when it got to the rinse cycle again with the F02 error. Check This Out Reply Meredith says: April 19, 2015 at 4:19 pm It worked! Using the guidance above, I removed the lower panel (mine had three bolts) and coin trap cover (be prepared for water) and found a small amount of the expected debris in Thanks, Matt Reply Missy says: May 22, 2015 at 11:34 pm Have done all the above, even used a wet vac to attempt getting out any thing that might have been Whirlpool Duet Error Code F11

Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU) Check Drive belt Check MCU Check Motor Check Wire Harness Sud SUDS LOCK (Overdose of Detergent detected Stunk to high heaven. If water is slowly filling the tub even when the washer is unplugged you need to replace the washer fill valves. http://bashprofile.net/whirlpool-duet/whirlpool-duet-washer-error-code-f1.html Remove the 3 Torx head screws (located left, center, and right) from the front bottom kick panel of the washer.

Matt Reply Mellisa says: May 22, 2015 at 4:51 pm Just wanted to add to the list of Thank You's! Whirlpool Duet F 02 Code Thank you!! It saved us $1500, I was ready to pay out for a new set, but this really does work.

You can also ask a question in our free DIY appliance repair forum located at the top of this page.

Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Then remove the trap completely to check it. 08/16/2014 by Andrew Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? F1E2 Error - Motor control fault. Whirlpool Duet Washer F2 Error Code Was this answer helpful?

Thank you for saving us some money! :-) 07/18/2013 by Vickie Kindl Thank you so much! Drum full of water - error codes - have to be up for work at 5. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. have a peek here Possible causes… 1.

Those two other cleanings did not fix the problem, but needed done anyway.