Cleared this out, reassembled and set washer to go. 3 full cycles in and working fine.....so far! This can hold air pressure in the tube keeping the pressure switch on. From this I surmise it is a software thing, perhaps the out of balance algorithm is less critical when not at full speed. (just a thought) I have also noticed that Thanks for the advice. Source
Advertisements Important Attempting repairs can be dangerous. This thread is now locked and can not be replied to. removed stick, screw and sock which was casing the problem! It once filled and then drained again.
Hotpoint Error Codes Flashing Lights
CRam December 2012 Cleaned the pump out and found hair bands, hairclips and £2.58 :) ............ Hairclip !!! Unsolicited PM's and emails will not be answered. Nicolas in Amstelveen October 2014 Absolute dream.
If not the pressure sensor what is convincing the machine it is full of water when it isn't ?
To find out how to mend it click here.
Thank you guys for all your help.
Household Appliances, Washing Machines (38550 other questions) Related questions - hotpoint, fault, code, f05, help Add a question Mend > Washing Machines hotpoint fault code F-05?
Most likely something caught in the pump which is accessed by removing the small panel at the rear/bottom of the machine. Unscrew the pump off or remove the pipes will reveal all. clicon357 Regular Forum User Posts: 39Joined: Tue May 31, 2011 9:32 am Reply with quote Re: Hotpoint WMD960 - F05 Fault by iadom » Sat Aug 18, 2012 2:25 pm Hotpoint Ultima Washing Machine Manual Back off, (2 screws) and the pump sits down on the bottom right.
Ours broke a couple of days before Xmas. Hotpoint Pump Filter Otherwise wait for engineer. After searching the compartment in front of the pump and its output for blockage I looked at the pressure switch and the area where it forms an intersection with the output
Thanks for the tips!
AJ says August 12, 2015 at 6:53 pm WMEF742P F05 error. Hotpoint Dishwasher Error Codes removed the front panel and cleaned the filter on the bottom right. Paul paul June 2007 f05 lights 2&4, pressure sw stuck on full call them out Anymore questions or parts required http://www.freewebs.com/msdapudsey1 Just go to the forum phil grimshaw May 2007 Thanks Andy Trigg says November 3, 2014 at 3:11 pm Hello Bernie, the F05 error isn't caused by a pump blockage, it's can be a blockage in the pressure system which
Hotpoint Pump Filter
Charged myself £20. On removing the filter cover found no blockages and on removing the pump also found no blockages. Hotpoint Error Codes Flashing Lights Followed instructions at the start and have everything at hand. Hotpoint Washing Machine Fault Codes unscrewed the plug/filter, then slowly taking the weight tipped the washer forward to fill the bowl, tip back to stop the flow, empty the bowl into the bucket and repeated till
F02 Motor circuit fault Issue: Intermittent or no drum rotation during wash The more detail and information you provide in your question the easier it is for others to help you. Hotpoint Washing Machine Problems
Reconnect supply, wait 30 seconds and try starting the machine again. Advice: We recommend you call our customer service centre to book an engineer on: 0344 822 4224
Help wanted! Hotpoint Ultima Problems Often you will find the sump hose blocked, again always with junk that should not have been put in the first place.Be sure to remove the plug and have a bowl offer | What's the catch?
The pcb is suspect after you've checked the pressure system and switch but it's always risky buying expensive parts which can't be returned if it doesn't fix the fault. So white clip off holding the drain hose on to the pump, white clip off holding the black sump hose to the pump and then removed the big spring clip on martin w January 2014 i also have the same code flashing on the machine and smell of burning pam December 2012 I need an answer to the same question Mary asked. Indesit Washing Machine F05 Error Code As a last resort I checked the drain pipe to the u bend and found it was half blocked.
Mend it How do I use my PC's Safe Mode? Over 50 more diy washing machine repair help articles covering most common faults. bumpkin 23:58 12 Apr 14 BRYNIT, I could not unscrew the filter as is was jammed by a coin so I had to remove it from underneath the machine and also Check This Out It would have saved me all that hassle with the baking tray!
Theresa December 2011 Paul's advice from June 07: (if the machine is still full, move the waste pipe lower than the drum into a bucket or pan this will empty Advice: Please disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Bullshit or not I don't know but I needed the thing working. More comments: (oldest on page 1)1 2 » Has this page answered your question?
As a last resort I turned my Hotpoint on it's side and decided to check the rubber hose leading from the washing machine to the filter. neil April 2012 Thank you for all these comments, I was able to fix my machine and feel very proud of myself! rocks1, 24 Apr 2012 #4 moleypoley Joined: 24 Apr 2012 Messages: 5 Thanks Received: 0 Location: Northamptonshire Country: Hi, had a look but nothing at all behind the kick strip (ive never had the problem again.
have a genuine no-strings trial offer. First time? Cleaned it all up and machine now works. That's a great story, I'm sure he would have fixed it though if you had given him chance ;) The bung by the way is there so that it can be
WHAT settings?(Added 53 min/s ago) The rinse light keeps flashing and beeping !!!!?(Added recently) peugot 307 brake switch?(Added recently) Beko dsc85w only heating on the first spin.?(Added recently) Advertisements Fixed! Was just about to call a repair man when I thought I may as well check the outlet pipe at the U-bend of the sink. took about 40 mins but second time would be much quicker. Thanks to everyone for the advice.
Good luck to all Guy August 2016 BIG THANK YOU to everyone, i found nothing wrong with my washing machine, than i looked at Gary`s comment and voila problem was in It will pump for 30 sec and th...Click here for the answerhow to fix a defy dtl125 error?Mashine dont spin give error E9...Click here for the answerHow to clean a hotpoint mend, fix, or repair just about anything. Albert March 2015 Just got 44 coins from the pump !