Home > Fax Error > Fax Error Power Failure

Fax Error Power Failure

View solution in context Reply 0 0 Jholder Grad Student Posts: 173 Member Since: ‎09-16-2011 Message 2 of 19 (1,196 Views) Report Inappropriate Content Re: Fax Failure Options Mark as New When a message is displayed on the LCD, check the cause. Wait until the transmission/reception is complete. If you unplugged the power cord after pressing the ON button to turn off the power (the POWER lamp is off), reconnect it, then press the ON button to turn on

Click "Go" and then click "Drivers". Scanned Documents have Lines and Streaks¶ If there are vertical bands, lines or streaks in your documents try the following solutions to fix the problem. Adv. Now inspect the cartridge by doing the following. her latest blog

Run a diagnostics test¶ Run a test to make sure your device is running properly. If you unplugged the power cord without turning off the power (the POWER lamp is lit), reconnecting it turns on the power automatically. Then select the "Tools" category and press "OK".

  1. Ensure that an error message is displayed on the touch screen.
  2. Delete contents in memory, then send a fax again.
  3. If the problem persists after doing these steps you may need to service the product. 0 Comments Add Comment Add Comment 1024 View Statistics: Past 24 Hours: 6 Past 7 Days:
  4. If the telephone line or connection is poor, reducing the transmission start speed may correct the error.
  5. You should download the firmware and follow further instructions given on the screen to completely update your device.
  6. Now try sending your fax again.
  7. Then turn the device off and disconnect the USB from the back of your device.
  8. LIST.
  9. Loading Originals Check10 Does a printer error occur?

Reply 0 Reply 0 0 OutOfTheBox Honor Student Posts: 4 Member Since: ‎03-25-2011 Message 2 of 2 (1,293 Views) Report Inappropriate Content Re: 49.0039 Error -- 'Power fail' on faxing -- After you have a replacement cartridge you will have to re-install it. To clean the cartridge contacts: Dip the cotton swab in distilled water, and then squeeze the tip to remove excess water. Click "Organize" again and then press the delete key to delete the files.

After the power failure report is printed, keep the machine turned on for about 24 hours to recharge its internal battery. Press the Power button to turn on the product.6. Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.Click on the BLUE KUDOS button on the left to look at this site On the bottom left of the Advance Search screen click the box next to "Include non-indexed, hidden, and system files (might be slow)".

When the error message without the support code is displayed, refer to A Message Is Displayed. If you unplugged the power cord after pressing the ON button to turn off the power (the POWER lamp is off), reconnect it, then press the ON button to turn on Check the Power Cord¶ The power cord could be loosely connected to the device or outlet. Solved!

Click the Start button and in the search bar type "%temp%" and press enter. You might need the direct power from an outlet. Basic Connection If the telephone line is connected correctly, there is a problem with your telephone line. How do I clear my printer of unwanted documents?

When the error message with the support code is displayed, refer to Support Code List. Run the fax diagnostic test by pressing Setup>Tools>Run Fax Test.And let us know the result of the fax test as mentioned in the Fax Test Report that prints out. Important Confirm that the POWER lamp is off before unplugging the power cord, then unplug the power cord. Error Codes in Fax Communication¶ If you're having problems faxing and the above solutions didn't work then your device might contain communication errors.

First turn on your device. The error messages will indicate the cartridge that is the issue. Why does my epson printer/fax machine keep telling me no dial tone whenever I try sending a fax? Then unplug power cord from electrical outlet.

Yesterday, in chat, the person on the other line had me discharge the machine, and I have no doubt that this will not solve it either, let alone that having to When you send a fax manually, dial the number with Enable selected for Hook key setting in Security control under FAX settings, or dial the number using the telephone connected to You cannot send faxes if the power is turned off.

With the battery fully charged, the machine is able to maintain faxes stored in the memory for about one hour in the event of another power failure.

Then reconnect the USB to the back of your device and load the paper in the tray. When an error message is displayed on the LCD, check the cause. View Solution. When I look in the event log, it says 49.0039 under error, with a page count.

Underneath this panel you will find your scanner glass. Remove the cartridge, and then place it on a clean sheet of paper with its nozzles facing up. When the installation screen opens click Exit. Add your answer Source Submit Cancel Report Abuse I think this question violates the Community Guidelines Chat or rant, adult content, spam, insulting other members,show more I think this question violates

Power on your device and try scanning a document. Ensure that the RJ-11 phone cable is securely connected to both the printer and the corresponding wall jack. If you are in a hurry, press the Stop button to close the message, then send the fax. Carefully slide the cartridge out to fully remove it.

Go to HP Drivers and Downloads and then type in your device model number. Make sure that the LIU, which is the box that the phone cord plugs into, is connected appropriately and that the LIU itself is securely connected. Thank you! Register · Log In HP Support Forum Home > Printers > Scanning / Faxing > Power Failure on fax report HP Support Forums Join in the conversation. Slide the new cartridge into the empty slot and push it forward until it clicks into place.

A Message for Faxing Is Displayed on the Fax Standby Screen Print ACTIVITY REPORT and check for an error. Click to download and follow the instructions given to you to save the software to your computer. Close the cartridge door and then reconnect the power cord. Ensure that an error message is displayed on the LCD.

Changing Registered Information Note You can check the registered information in the machine's directory by printing RECIPIENT TELEPHONE NUMBER LIST. Try scanning a document. Check off your operating system and then click next. Press the power button and wait for the cartridge to be idle.

this printer doesnt have a firmware update for it. A Message for Faxing Is Displayed on the LCD Print ACTIVITY REPORT and check for an error. If you still cannot send the fax, select OFF for Dial tone detect in Advanced FAX settings under FAX settings. when I went to start it up it now tells me "Fax Failure" I have tested the line and a diffrent fax dose work.