Home > Fax Error > Fax Error Code 212

Fax Error Code 212

There was a communication error with the sending fax machine. If this is the case, ask the sender to retry a normal transmission from the remote machine. Configure the remote machine for reception. Turn the printer off, then on. weblink

Turn the printer off, then on. Support Home Page Phaser 750 Support PageXerox Office Support Home Additional Information Register your Printer ASPs & TPMs About Software Support Color Connection Printer Warranties Material Safety Data Sheets Supplies & This prevented the fax from receiving any more pages, and caused it to terminate the session prematurely. Communication error occurred during high-speed transmission. http://www.fixya.com/tags/panasonic_fax_error_code_212

Turn the printer off, then on. Also make sure the remote machine is attempting to initiate a transmission and not a reception. 243 244 The user of the remote machine pressed the Stop key, causing the session Replace the Toner Cartridges. Confirm that the remote user has the correct password, and that the local machine is configured with the same password, if this option is available. 230 The remote machine attempted to

All rights reserved. Error 20 Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Error 61 Remove and re-install each Toner Cartridge. Communication error occurred during transmission.

It can also be caused if the receiving fax is using a fax format incompatible with the HP fax (usually during color faxing). Turn the printer off, then on. Remote diagnostics cannot occur between machines with incompatible remote versions. 316 The local machine is set to initiate document transmission, but detected that the remote machine is not able to receive If the document is large, ask the remote user to re-send the document as two or more smaller documents.

Ask the sender to remove the fax number from the diagnostic check. 227 The remote machine attempted to initiate a fax session at a speed and modulation that the local machine Enable ECM on both the local machine and the remote machine. 231 The remote machine attempted to initiate a transmission to the local machine, but the receive capability was disabled at Contact the sender to make sure a document is ready and correctly loaded in the sending fax machine. Z7_3054ICK0KGTE30AQO5O3KA30H5 hp-country-locator-portlet Actions ${title} Loading...

Error 62 Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser). http://www.worldoffax.com/PANASONIC%20UF%20595%20ERROR%20CODES.htm If the error persists, and error correction is in use for the fax session, disable ECM. NOTE If the communication error occurs frequently, change the default setting of TX Start Speed in System Menu. Try turning on Silent Detect in the Fax settings.

Call the telephone provider if line conditions fail to improve. have a peek at these guys If ECM is enabled, then disable it. Turn both the sending and the receiving machine off for ten seconds, turn them on, and then try sending again. Use the tables in this document to view fax error codes and solutions.

Try sending the fax again. 312 A remote fax machine failed to answer the call. Remote diagnostics cannot occur between machines with incompatible remote versions. Turn the printer off, then on. http://bashprofile.net/fax-error/error-code-345-when-i-try-to-fax.html Select a slower reception speed.

Journal comm. 212 What do I do? Z7_3054ICK0KGTE30AQO5O3KA30N0 hp-concentra-wrapper-portlet Actions ${title} Loading... The remote machine failed to respond to a fax command from the local machine because the connection was interrupted.

Send or receive again.

PDF Manual Panafax UF-490.pdf.... Both machines have attempted to start a reception at the same time. Try the fax when telephone line conditions have improved. Panafax UF-790 Plain Paper Laser Fax...

Send again. However, the ability to receive the entire document improves. Panafax UF-790 Plain... this content Reconfigure the local fax machine to use different configuration settings, enable or disable the ECM setting. 245 ECM 246 ECM The user of the remote machine pressed the Stop key, causing