Home > Fax Error > Fax Error 0080

Fax Error 0080

A. Solution: Replace the Thermistor Assy. ##054 [ TX / RX ] Image Memory backup error. Solution: Refer to Service Manual. ##304 [ RX ] Fail memory copy failure. A.

Solution: Replace the DECODE control unit (PRINT, etc.). ##238 [ RX ] PRINT control unit malfunction. A. D. Solution: Replace the board containing a printer control ROM B. weblink

Cause: Abnormal protocol. A. Cause: BJ printer control ROM error Solution: Power cycle the machine (unplug unit). Solution: Boost the transmission level so that the other party can receive NACK properly.

Solution: Adjust the NL equalizer so signals from the other party can be received properly. Solution: Lower the transmission start speed to 4800 bps. Dec 12, 2009 | Fax Machines 1 Answer From one source only when they try to send a FAX to my HP Officejet v40 machine, 80% of the time I get Solution: Adjust the NL equalizer so the other party can receive picture or EOM signals properly.

B. Solution: Replace the read end sensor. ##503 [ TX ] Fail MCF1 or PIS reception during G1 transmission. A. Loading...Oops :Please try again.

I only noticed it not working about a week ago. A. Solution: Replace the SCNT PWB. ##100 [ TX ] Excessive repeat protocol during transmission. Cause: Other party cannot receive DIS signal properly due to poor line conditions.

  • Cause: The ink sensor is defective.
  • Cause: The called party disconnected the line during phase 3 or unable to detect the signal from the called party.
  • A.
  • Solution: Have the other party boost the transmission level to receive the signals properly. ##731 [ RX ] REJ reception after picture reception during ARQ.
  • Solution: Have the other party lower the reception level to prevent the other party from receiving echo signals. ##509 [ TX / RX ] Failed to detect end of Tonal
  • Cause: SCNT PWB malfunction.
  • Cause: Defective internal unit.
  • Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##292 [ RX ] Fail to detect EOL at the start of

Cause: Other party confused by echo and does not send G12. Solution: Boost the transmission level so the other party can receive CFR2 properly. Cause: The UPI to control the ENCODE did not function properly. Please try the request again.

A. Note: if the capacity of the absorption pad is unclear, register a value corresponding to the quantity of absorbed ink in pad Solution: Replace the PCNT PWB, and register a Transmission Error Correcting Mode was used. Cause: Proper carrier signal at the start of the picture signal was not received due to poor line conditions.

Solution: Perform echo counter-measures as listed in Service manual. A. Solution: Have the other party boost the transmission level so picture signals can be received properly. Use the arrow buttons ( ) to select On or Off , and then press the OK button ( ) to confirm the setting.

B. A. If the machine is in sleep mode it can cause this as well to take it out of sleep mode press the [Energy Saver] button.

What is support code C000 10/13/2016 10/13/2016 Nathan I have a canon MG5420.

Cause: Cannot receive protocol properly from the other party due to poor line conditions. Cause: The Thermistor is defective. Question about FAX L-120 Plain Paper Laser 1 Answer Error comm 0001 error comm 0001 Generally this error(Error 0001) is observed while receiving Fax. Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the

A. Solution: Transmit to a FAX whose bits 33 and over are not defined. ##200 [ RX ] Fail to detect picture reception carrier for 5 seconds during reception. characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 125 11321693 Search Fixya Press enter to search. Solution: Replace SCNT. ##222 [ RX ] 90% compression recording crystal breakdown.

Solution: Replace carriage cable with one that has a home position sensor attached. Solution: Have the other party boost the transmission level to receive picture signals properly. ##612 [ RX ] Fail to detect picture signals for 5 seconds after CFR transmission during A. Solution: Refer to Service Manual. ##302 [ TX ] Interface error between reader and controller.

Cause: Defective internal unit; (EEPROM write error). Solution: Replace the board containing the BJ controller C. Solution: Adjust the NL equalizer to receive the phase signal properly. ##607 [ TX ] Fail CFR reception during MF1 transmission. Make sure that it gets a dial tone.If none of that works next try a power cycle in case the machine is overheating and that is causing your error.

Communication was interrupted as a preventative measure since there was a mechanical abnormality in the document transport unit.