Home > Fax Error > Canon Fax Error Code Ng

Canon Fax Error Code Ng

Contents

Remedy Delete the unnecessary documents and documents with errors from memory to increase the amount of available memory. (See "Scan and Store," "Fax/I-Fax Inbox," and "Access Stored Files.") #107 Cause 1 B. Cause: The other party cannot receive NACK signals properly due to poor line conditions. Solution: Replace gear unit. weblink

An error occurred on the server side during transmission. Solution: Have the other party lower their transmission start speed to 4800 bps. A. A.

Canon Fax Error Code Ng

This error might be associated with bad line conditions or might indicate a problem with the fax's modem. Q.Is the toner cartridge installed properly? A. How to Change the [SMTP AUTH] Setting (MF4680) (See the relevant title in Related Information at the end of this page.) Other error code ([#xxxx]) is displayed.

Interpreting fax receive error codes This table contains fax receive error codes. Cause: The ink sensor is defective. Solution: Replace the backup battery. Fax G3 The machine will not print faxes, reports, or lists when paper is loaded in the multi-purpose tray.

TX/RX TIME The time taken (in minutes and seconds) to send the document from start to finish is printed. Enable or disable the ECM setting. Alternatively, stop the PServer. #818 Cause 1 The received data is not in a printable file format. http://www.imagerunneradvance.com/c5000_manual/contents/ssend_029b/func.html Cause: The waste ink pad of the cleaning absorption is full.

Contact the destination; the number may be a Voice/Fax number and needs to be switched to fax to receive your transmission. Toshiba Fax Error Codes Solution: Replace the thermal head. Cause: Other party cannot properly receive signals due to poor line conditions. Cause: Abnormal protocol.

  • Cause: Carriage motor does not work.
  • Solution: Turn off the power and unplug the unit.
  • Solution: Boost the transmission level so the other party can receive MCF2 or PIS.
  • Remedy Check TCP/IP Settings in Network in Preferences (Settings/Registration). (See [TCP/IP Settings] in "Settings/Registration Table.") #761 Cause 1 A PDF or XPS file with a digital signature could not be sent
  • Action Check the POP Server password in E-mail/I-Fax Settings in Network Settings in System Management Set (from the Additional Functions screen). #0813 Description The POP Server name setting is incorrect.

Canon Fax Error Codes

Cause: Defective internal unit; (LBP VSREQ does not go off). http://support.hp.com/us-en/document/buu02549 Cause: Cannot receive picture signals from the other party properly due to poor line conditions. Canon Fax Error Code Ng JOB NO. Canon Fax Machine Error Codes Remedy Re-enter the group destination, and try sending again.

Cause: Thermal head trouble Solution: Replace the Thermal head B. http://bashprofile.net/fax-error/error-code-345-when-i-try-to-fax.html Cause: The CS motor does not run. Solution: Contact the telephone company and request line maintenance. ##010 [ RX ] Failed Phase synchronization on first sheet during reception in G2 or MF1. Cause: SCNT PWB malfunction. Fax Error Codes Ricoh

Cause: The absorption pad for the maintenance jet is full of waste ink. Cause: The other party experienced echo malfunction. An error occurred on the server side during transmission. check over here Visit now Z7_3054ICK0KGTE30AQO5O3KA30H4 hp-feedback-banner-portlet Actions ${title} Loading...

B. Canon Error #099 Cause: Defective internal unit; (byte pack interrupt was not generated). A.

Check the network status. #815 Cause 1 You cannot log on to the file server because the machine is printing a document sent to that server.

See [Format PDF to PDF/A] in "Settings/Registration Table." Remedy Cancel the Encrypt and Visible Signatures settings. Cause: Cannot receive the picture or EOM from the other party properly due to poor line conditions. Press [Off] if you do not want to print it. Canon Fax Error #099 A.

A. Try sending again. A. this content Action Start the Remote UI and make sure that the E-mail Address in E-mail/I-Fax Settings under Network Settings is set correctly. #0802 Description1 The name of the SMTP server is incorrect.

Solution: Adjust the NL equalizer to receive the phase signal properly. ##607 [ TX ] Fail CFR reception during MF1 transmission. A.Check the network status. [#0753] is displayed. Solution: Refer to Service manual ##311 [ RX ] Control error. Cause: The operation of the UPI to control the G3 modem did not finish properly.

Solution: Have the other party lower their transmission speed to 4800 bps. Cause: The actuator malfunctions during cleaning. Retry the fax reception when telephone line conditions have improved. Solution: Power cycle the machine (unplug unit).

Solution: Power cycle the machine (unplug unit). Remedy Delete the unnecessary documents to make more memory available. (See "Scan and Store," "Fax/I-Fax Inbox," and "Access Stored Files.") Cause 3 The scanned document cannot be stored because there are D. D.

Try the fax when telephone line conditions have improved. Select a slower reception speed. Remedy Delete the unnecessary documents stored in the Mail Box and the Fax/I-Fax Inbox. (See "Scan and Store," "Fax/I-Fax Inbox," and "Access Stored Files.") #713 Cause 1 The document in the Remedy Set the Different Size Originals mode, and then try scanning again.

B. Cause 3 You are sending a file to a destination to which you have no write permission. Cause: SCNT PWB malfunction. Cause: Cannot receive signals from the other party properly due to poor line conditions.

Solution: Adjust the NL equalizer so that the other party can receive the picture or EOL signals properly. Solution: Leave powered ON for 5 days, battery will recharge, but data has been cleared.