Home > Error Code > Whirlpool Washing Machine Error Codes E1

Whirlpool Washing Machine Error Codes E1

Contents

Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. CA or CI Average current limit or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return If all connections are good, then check the individual switches as outlined for the F5 failure. ^ top 2 Digit Failure Codes F0 Board failure Replace control board (also called ERC Some terms used on this page... http://bashprofile.net/error-code/whirlpool-washing-machine-error-codes.html

Range manuals Don't know a thermostat valve from a safety valve? If your Whirlpool electric... All rights reserved. As always, disconnect power on any control you're disassembling or assembling. http://www.partselect.com/JustForFun/Whirlpool-Appliance-Fault-Codes.aspx

Whirlpool Washing Machine Error Codes E1

Remember that self-cleaning oven latches are slow-moving. Whirlpool produces a variety of... The washer does not flash "PF" when it is first plugged in.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. Top 4 Reasons Surface Element Is Not Working? Ld - Long Drain - This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. Whirlpool Microwave Error Codes by Maira ESTRELLA Earned 1,044 community points in Click'>Appliances August 28th, 2012 Answered in 15 hours Comment 0 votes Didn't find what you are looking for?

If no damage to wires and all connectors okay, proceed to step C. Whirlpool Range Error Code F9e0 You may be able to trace the problem to a defective keypad or EOC or ERC (Electronic Oven / Range Control; essentially the clock unit,) but often the diagnosis is ambiguous. If problem has not been corrected, replace the pump. If “Sud” is displayed a potential suds lock is detected.

Ste. 500, Encino, CA 91436 1-877-477-7278 Tennessee 240 Edwards St. Whirlpool Accubake Oven Error Codes Check all connections at control board and at the latch switch and door switch. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). F1-E5 - Calibration Shifted - Disconnect power for at least 30 seconds and then reconnect.

Whirlpool Range Error Code F9e0

ERC - Electronic Range Control. http://www.shopyourway.com/questions/1183452 Also check for any causes of high resistance in the oven temperature sensor circuit. Whirlpool Washing Machine Error Codes E1 Oven temperature sensor - What a common sensor or temp sensor looks like. Whirlpool Top Load Washer Error Codes If damage is found, replace appropriate part.

F07 Motor control unit error The Central Control Unit has detected a short in the motor control unit. Check This Out The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. F02 - Long Drain (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. If you find that the door or the latch switch do not function, you may need to replace them. 4-Digit Error Codes On some Whirlpool ranges, the error codes have four Whirlpool Top Load Washing Machine Error Codes

  1. Gas Burner Sparks All The Time?
  2. out of box M Get Weekly DIY Guides & Inspiration Life Made Easier.
  3. Check CCU is also operational by performing a diagnostic test or any cycle.
  4. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
  5. For this reason, I caution you: IF YOU ARE NOT SURE OF YOUR DIAGNOSIS, CALL A QUALIFIED, FACTORY-AUTHORIZED TECHNICIAN to diagnose and repair your oven.
  6. F7 - E1 Common switch wire is defective Common wire (+5VDC) to latch switch, and to door switch is shorted to chassis ground or neutral.
  7. I had so many questions and they answered them all." Sharon S.
  8. Also check the motor and wire harness.
  9. Look for welded relay contacts on bake or broil relays.
  10. F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

See Details More Products Whirlpool WOS51EC0AS 30" Electric Wall Oven w/ ... Press any "stop," "reset," "clear" or "off" button, wait for a few minutes and remove power from the unit, either by unplugging it or turning the breaker off for a few DOUBLE OVENS Most double ovens have two control boards. Source codes except F1-E3.

There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. Whirlpool Oven F2 Beeping If error persists, you can contact customer service and let us know. F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check all connections to the water temperature sensor, heating element and element relay.

demandmedia.com © 1999-2016 Demand Media, Inc.

Top 5 Reasons Electric Oven Temperature Is Incorrect? Press STOP/CANCEL to clear the display. F1 - Control Board Failure - Replace control board (clock). Whirlpool Oven Error Codes E2 F3 Reconnect the unit and power to verify the pressure switch is operational, as well as the flow meter (blow air through the flow meter and measure resistance).

Press STOP/CANCEL to clear the display. F1 Board failure Replace control board (also called ERC or clock). The unit will attempt the clean out the suds three times before displaying this error. have a peek here Note: Unit will attempt to unlock itself during this error six times before displaying this error code.

Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in. Check wires and connectors from control to door switch, then from door switch to control. Du kannst diese Einstellung unten ändern. Check keypad connector for firm connection (keypad connects to control board). 2.

FdL Door lock error A Door Lock Error occurs if the door cannot be locked.