Home > Error Code > Whirlpool Duet Washer F11 Error Code

Whirlpool Duet Washer F11 Error Code

Contents

See Details Whirlpool WTW8500DC 5.3 cu. Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus! Offer valid for online purchases only. You have reached the maximum number of models that can be added to your list. Source

LS - Lid Switch Error - This error will occur if unit cannot detect the lid switch opening or closing. E2 - Shorted Thermistor - Replace thermistor. Bought a new washer instead of spending $400.00 for a motor. F2-E1 - Touch Pad (Keypad) Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.

Whirlpool Duet Washer F11 Error Code

Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. Replace failed component. www.CircuitBoardMedics.com Was this answer helpful?

  • What problem could this be?
  • Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
  • Answered!

F1-E5 - Calibration Shifted - Disconnect power for at least 30 seconds and then reconnect. So if you get the error intermittently try cleaning up the power and post whether it's fixed. If there is water in the unit, verify the drain pump is working and the pressure switch hose is in good condition and properly connected. Whirlpool F11 Code Fix Still need help?

Since still covered by Bestbuys PSP they sent out a service tech who inspected the washer but ended up doing nothing more than cycle the power and reseat some connectors. Whirlpool Duet Washer F06 Error Code CST Sat 7:00 a.m. - 9:00 p.m. The motor carbon brushes transfer the electricity from outside the motor to the spinning winding in the center of the motor. see this here Anmelden 12 Wird geladen...

Not very common today. What Does F11 Mean On My Whirlpool Washer Is there any help out there? Note: Unit will attempt to lock itself during this error six times before displaying the error code. I made sure both parts were properly attached.

Whirlpool Duet Washer F06 Error Code

Brand WHR Media faulttree Topic assistance Tags This page has no tags. © Copyright 2016 Whirlpool Home Appliances Powered by MindTouch Fixitnow.com Samurai Appliance Repair Man Your appliance repair weapon http://fixitnow.com/wp/2008/10/28/whirlpool-duet-washer-with-an-f06-fault-code/ All rights reserved. Whirlpool Duet Washer F11 Error Code I'd sure like to find it while it's still covered by the extended warrantee. Whirlpool Duet Washer Error Code F06 E01 Post navigation ← New and Improved Three-Step Samurai Appliance Repair Program and Appliance Repair FAQ Pages How to Repair a Dishwasher → Leave a Reply Cancel replyYou must be logged in

Possible Solutions Did you receive a F6E2 washer reboot alert? this contact form Check the drive system for any worn or failed components and reconnect power and plug unit in. Brushes often fail on the Spin Cycle first. I tried canceling the cycle and moving to the drain and spin cycle. Whirlpool Duet Front Load Washer Error Code F11

Press and HOLD start to continue the cycle, or press 'Stop/Cancel' to clear display and cancel cycle. Was this answer helpful? Press and HOLD start to continue the cycle, or press off/pause to clear display. http://bashprofile.net/error-code/whirlpool-duet-washer-error-code-e02.html What do you recomend to me to check or replace the module.

I revised visually the motor driving PCB ( EE36.2 AEG 645 182 180) and seems to be ok, but there are a lot of discrete components that may be failled. Whirlpool Dishwasher F6 Error Code A recap: First service visit the connectors between motor control board and motor were reseated (unplugged and plugged back in) this "fixed" the problem for 4 months. 2nd repair attempt- this If damage is found, replace appropriate part.

Any other suggestions?

Please Sign In or Register to have unlimited usage. At the opposite end, this is the 4th connector from the right on the front of the CCU. Press 'Stop/Cancel' to clear display. F20 Error Code On Whirlpool Washer F9 - Oven Door Lock Failure - Check door lock switches and wiring.

At the opposite end, this will be the 2nd connector from the rear on the left-hand side of the CCU. Now turn the motor pulley (sans belt) by hand. However, before the code comes up, the door locks and it fills with water. http://bashprofile.net/error-code/f06-error-code-whirlpool-duet-washer.html Washer worked fine until this last weekend and now is exhibiting the same problem.

woody 07/30/2011 by woody wood You are welcome and good luck to you. 07/30/2011 by oldturkey03 Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this