Home > Error Code > Whirlpool Duet Washer Error Code E02

Whirlpool Duet Washer Error Code E02

Contents

Now I have a spare new one in case my fix isn't long term. This means that the dispenser motor which directs fill water to the appropriate dispenser area, is not moving properly. I actually took apart the door lock and fixed it while waiting for the new one to come from EBay. Verify there is not a siphon problem.2. Source

Take readings as listed and also double check the connector to make sure it is not oxidized. Your Duet washer has detected that it is full of soap suds which are difficult to drain. the wire on the water sensor was broke inside the connector. 110.00 in parts and a 135.00 service call later lol. lets stick with the wash cycle, if i shorten the wash cycle it will still error code out after a couple of minutes but useing the pause trick will not work

Whirlpool Duet Washer Error Code E02

If the sensor doesn’t correct the problem there may be a loose or bad wiring connection or you may need to replace the control board. The best way I have found to deal with the water when your washer's drain pump isn't working is to use a shop vac and pull from the drain hose. Locate the Central Control Unit (CCU) directly behind the wash tub.

  1. Check that water is getting to the steam valve, it may be blocked or restricted.
  2. Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help
  3. See Details More Products Kenmore 41162 4.3 cu.
  4. ft.
  5. Try a new cycle using just COLD ONLY, then start another new cycle with just HOT ONLY, then start another new cycle with just WARM ONLY.
  6. The part was MAYTAG WHIRLPOOL WASHER LATCH W10443885.
  7. The material isalready there...do you have a multimeter?

The sensor (NTC) is located at the base of the wash tub in the front on the heating element. Logged May the hinges of our friendship never grow rusty.About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 There are a few helpful things to note here. Whirlpool Washer Error Code E03 Thanks in advance for the help! 4 commentsshareall 4 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–]Junkmans1 0 points1 point2 points 11 months ago(1 child)I'd go with swapping out the door lock.

with the reddish wires attached duet with bottom flap removed.jpg (54.71 kB, 506x435 - viewed 2953 times.) « Last Edit: December 11, 2010, 10:34:15 PM by JWWebster » Logged May the F05 Error Code Whirlpool Microwave If the sensor checks good, take a reading across the heating element terminals. Simple approach if you do it by the book. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Check that the drain pump is working properly. 3.

Unplug washer or disconnect power.3. Whirlpool E03 Error Ask a question Get up to 45 % off On Washers Related Questions Related Questions'>What does the F06 error code indicate on my Kenmore HE3 washer? 1 answer Related Questions'>What does Might be due to a bad heating element. (anormal = infini)and such. If it doesn't work then you almost certainly have a clog in your Duet washer's drain system and the pump may be fine.

F05 Error Code Whirlpool Microwave

You will also want to check the pressure sensor (Duet Washer Pressure Sensor Check) F3E2 Error - Temperature sensor fault.

Get more answers from the people in your networks Tags Kenmore , Washers Click to remove this tagging. Whirlpool Duet Washer Error Code E02 You will need to remove the rear panel to access the heater and thermistor. Whirlpool Washing Machine Error Codes E1 If by chance you weren't banned the first time we will find you and leave negative reviews on your business.

If I find it, is there a way to test it or do I just replace it?Thanks for the help! this contact form F1E1 Error - Main control fault. I thought this model didn't come with a heating element but I will look when I get home. Category:Appliance Share this conversation Expert: Tom Johnston replied6 years ago. Whirlpool Error Codes

model number GHW9100LQ after searching your site a little more it looks like a temputure sensor mite be the problem. Check the heating element for continuity with an Ohm meter. This is a rare one but it means that something is wrong with the washer cycle that was selected. have a peek here Your question was published, help is on its way!

Top 3 Reasons Top-Load Washer Won’t Drain? Whirlpool Washer F5 Error Code You can test this machine fully with the bottom panel off. 1. If you need to post a picture, put it in your post linked to imgur.

ft.

If you get this error... 1. They are not real expensive if you shop around online, much less than a service call, so it would be a good starting point and likely take care of the problem. permalinkembedsaveparentgive gold[–]humedav 0 points1 point2 points 9 months ago(1 child)Hey, I'm currently getting this same error. Whirlpool Duet Error Code F05 E03 Check the water temperature sensor.

Unplug washer or disconnect power.3. F0E1 Error - Load detected during a clean cycle fault. ft. http://bashprofile.net/error-code/f06-error-code-whirlpool-duet-washer.html Check the pressure switch.8.

Logged "It's only expensive if someone else fixes it for you"- The Virtual Repairman www.repair2000.com jracmm VIP Member Member Since: Dec 2008 Posts: 10 Re: Whirlpool Duet Washer giving error code your washer may need a new main control board. or so it will restart and finish the cycle. Drying, 10/14/2016 10/14/2016 JACUSTOMER-x0uwnnmp- Whirlpool refrigerator model GX5SHDXVQ02.

The letter sends me email.I love fan letters! If water is slowly filling the tub even when the washer is unplugged you need to replace the washer fill valves. F8E3 Error - Overflow fault. Add your answer Sign in to answer a question 1 Answer from this member: The "F05" error code is indicating a Water Temperature Sensor Error.

Verify pressure switch operation.7. Jump to content Samurai Appliance Repair Man's Blog Existing user? To access, you will have to UNPLUG your washer and remove the lower access panel under the door. or so it will restart and finish the cycle.

Readings will be as follows:Temperature Meter Reading32°F (0°C) 35.9 K ohms86°F (30°C) 9.7 K ohms104°F (40°C) 6.6 K ohms122°F (50°C) 4.6 K ohms140°F (60°C) 3.2 K ohms158°F (70°C) 2.3 K ohms203°F