Home > Error Code > The Print Spooler Failed To Delete The File Error Code 0x2

The Print Spooler Failed To Delete The File Error Code 0x2

Contents

So I looked up Error 0x490 and got this article on the subject. But then next time I shut it down, it fails to reboot again. I don't know what to do, I hope you can tell me. Afterwords it did boot up to Vista, but bluescreened after sitting for a while. http://bashprofile.net/error-code/file-setupdd-sys-could-not-be-loaded-the-error-code-is-4.html

Like I expected I got a BIOS error screen telling me there went something wrong and asking to start normally or to start startup repair. Error code = 0x0 Time taken = 0 ms Boot manager generic failure 0xc000000e Test Performed: --------------------------- Name: Event log diagnosis Result: Completed successfully. The filesystem on the boot partition can become corrupted as a result of an unsafe shutdown, sudden power loss, unsafe removal of local and/or external drives, or physical damage to your Symptom 1: Startup repair fails with message "Boot manager failed to find OS loader" When attempting to use the automated repair feature of Startup Repair, it attempts to repair your PC Read More Here

The Print Spooler Failed To Delete The File Error Code 0x2

This file can be deleted due to a failed Windows Automatic Update installation, a failed attempt at upgrading the OS, or by viruses and other malware. Error code = 0x0 Time taken = 0 ms Test Performed: --------------------------- Name: Disk failure diagnosis Result: Completed successfully. Your cache administrator is webmaster. Startup Repair runs but fails to repair, "If you have recently attached a device, remove it and restart".

  1. Thank you in advance for any help with this problems.
  2. Most are DCOM and Service Control Manager Eventlog Provider errors, which I can detail if requested, but the most serious looking errors are the following: (Source / Event ID / Task
  3. I do have a tool for reimaging the drive but I don't really want to go that far unless I have to.

Boot error Started by Trent M , Jul 02 2009 05:01 PM Please log in to reply #1 Trent M Posted 02 July 2009 - 05:01 PM Trent M Member Member Free space verification is complete. I formatted it, used DiskManagement on my son's computer to initialize it, DiskPart to turn it into GPT (since the Gateway uses UEFI) and finally got it to start loading the 0x2 Error Code Task Scheduler Repair action: File repair Result: Failed.

It will start quite happily in safe mode, I did the msconfig thing and turned off all the bits in as per another thread and all the start up stuff but Error Install Motioninjoy Driver Fail Error Code 0x2 A case like this could easily cost hundreds of thousands of dollars. boot critical file is corrupt. https://neosmart.net/wiki/failed-to-find-os-loader/ Get a discounted price on replacement setup and installation discs: Windows Vista, Windows 7, Windows 8.

EDIT: I can boot into Safe Mode now; I am trying the msconfig fix that Microsoft suggested EDIT #2: Nope. Fatal Error U1077 Return Code 0x2 Back to top Back to Internal Hardware 0 user(s) are reading this topic 0 members, 0 guests, 0 anonymous users Reply to quoted postsClear BleepingComputer.com → Hardware → Internal Hardware The results(cmd after test): C-drive Code: X:\Sources> chkdsk c:/f/r The type of the file system is NTFS. My drive is from Seagate.

Error Install Motioninjoy Driver Fail Error Code 0x2

You can rebuild the BCD using bootrec.exe, a tool built found in the Windows Recovery Environment. try this i have run /fixmbr and /fixboot also, and these succeded, but still the same error. The Print Spooler Failed To Delete The File Error Code 0x2 Failed to transfer logged messages to the event log with status 50. Regqueryvalueex Failed With Error 0x2 Short generic 6.

Not sure what happened, or if I did something incorrectly. his comment is here I ran the LIst Partition command in DiskPart and got the following: 1 Recovery 400MB 1024KB (offset) 2 System 300MB 401MB 3 Reserved 128MB 701MB 4 Primary 277GB 829MB 5 Recovery Open ‘Computer and browse to the location: C:\Windows\System32.2. Error code = 0x0 Time taken = 0 ms Test Performed: --------------------------- Name: Disk failure diagnosis Result: Completed successfully. Error Code 0x2 Onenote

Edit: I wrote the data in table format but it got put together by the software this site uses... It's available for Windows 8, Windows 7 and Windows Vista. Clicking to view the contents of Startup Repair's "Diagnosis and repair details" reveals the error to be "Boot manager failed to find OS loader" with one or more failed repair attempts. this contact form More Information Linked Entries bootrec Support Links Easy Recovery Essentials for Windows - our repair and recovery disk.

My question is, is my assumption of a bad windows update patch correct? Error 0x2 Setting Sddl On Driver File Is the only thing i can do let it restart and restart... Her only computer is the problem, so she can't directly search for fixes.

My System Specs You need to have JavaScript enabled so that you can use this ...

Drive Information 5. Edited by AustrAlien, 09 November 2012 - 06:07 AM. Error code = 0x0 Time taken = 47 ms Test Performed: --------------------------- Name: System boot log diagnosis Result: Completed successfully. Motionjoy Error 0x2 I get the following: Root cause found: bugcheck c000021a.

Success? So, here's the problem. Synopsis The error "Boot manager failed to find OS loader" is displayed when Startup Repair fails to correct problems with a non-booting PC. navigate here Fix #2: Use the System File Checker Windows Setup CD/DVD Required!Some of the solutions below require the use of the Microsoft Windows setup CD or DVD.

I believe that there's a SRTtrail.txt report that's generated at %WINDIR%\System32\LogFiles\Srt\SrtTrail.txt 0 #8 Trent M Posted 09 July 2009 - 09:21 PM Trent M Member Topic Starter Member 47 posts Hello, Error code = 0x0 Time taken = 0 ms Root cause found: --------------------------- Boot critical file d:\windows\system32\drivers\wrqpfogq.sys is corrupt. To fix the problem: .... 3) Repair you computer. Back to top #5 AustrAlien AustrAlien Inquisitor BC Advisor 6,772 posts OFFLINE Gender:Male Location:Cowra NSW Australia Local time:10:45 PM Posted 10 November 2012 - 04:03 AM Sorry about the delay

Error code = 0x0 Time taken = 110 ms Test Performed: --------------------------- Name: Internal state check Result: Completed successfully. Be patient while PartedMagic loads into memory, and then displays its Desktop. I'll try your other suggestions and I'll let you know if the utility discovers anything. System Manufacturer/Model Number Self Build OS Vista Ultimate x64, SP2.

Insert your Windows installation DVD into your PC's CD-ROM drive, Fully power down your PC, and make sure it has fully shut off, Power up your PC, Press any key when Then it restarts and boots fine. Even disabling ALL the services didn't work windows-vista boot system-restore share|improve this question edited Dec 13 '11 at 3:43 asked Aug 28 '11 at 4:42 Nate Koppenhaver 2,77132250 add a comment| Do you have access to a USB DVD Drive ? (use instead of internal DVD drive) How did you test the Hard drive ?