Home > Error Code > F27 Error Code Kenmore

F27 Error Code Kenmore

Contents

Was this answer helpful? What can I do? Report This by Manage My Life August 8th, 2010 Share it! Check the motor and do a continuity test. 3. Check for continuity of the User Interface harness. 2. Source

During the Cleaning Cycle was load detected inside the drum and Cleaning Cycle was interrupted by indicating “rL” to User. Wird verarbeitet... Unplug washer or disconnect power. 3. First time?

F27 Error Code Kenmore

Perform test program. Replace MCU board. F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle.

Check the pressure switch for proper operation. Replace User Interface. The washer does not flash "PF" when it is first plugged in. Whirlpool Washer Press STOP/CANCEL to clear the display.

Door switch/lock unit failure. 1. Whirlpool Washing Machine Fault Codes Check for Drain Pump Failure. 6. Refer to the Continuity tests. http://www.justanswer.com/appliance/3s27a-f27-error-whirlpool-duet-washer.html Unplug washer or disconnect power for two minutes.

Check Pressure Switch for correct working with a DVM/VOM. 3. If the above does not correct the problem, go to step 7. 7. Plug in washer or reconnect power. 6. The failure will be reset after running the Diagnostic Test Program.STEAMER DEFECT The Steamer temperature has not reached the correct value.

Whirlpool Washing Machine Fault Codes

Unplug washer or disconnect power. 2. Press CANCEL and observe for 1 minute to ensure operation is correct. 2. F27 Error Code Kenmore Replace door switch. Whirlpool 6th Sense Washing Machine Error Codes The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician.

Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen... this contact form F61 STEAMER COMMUNICATION FAILURE An incorrect or corrupted communication between Central Control Unit (CCU) and steamer electronic board is recognized. Fault find Click here to fix Magic Chef products. If you remove any connectors, make sure you write down where they go. Whirlpool Duet Dryer Error Codes

Replace Central Control Unit if drum is not moving F71 USER INTERFACE HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen... It will try to lock it 6 times before displaying the error. have a peek here Also I get code f99.

Door lock mechanism is broken. Wird geladen... F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1.

Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse,

  1. F27 OVERFLOW CONDITION If the overflow contact on the pressure switch is closed for more than 60 seconds, an Overflow Condition occurs.
  2. Some models do not have the display to show the failure codes.
  3. F70 CENTRAL CONTROL UNIT HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface. 1.

Check door switch/lock unit. 3. Unplug washer or disconnect power. 8. When I go to start the cycle door clicks drum rotates and then water leaks 1 answer Related Questions'>I have whirlpool Duet sport and get a error code F-33, help? 1 ft.

Diese Funktion ist zurzeit nicht verfügbar. If door latched: A. Unplug the unit to service. Check This Out Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive.

Try unplugging the Unit for two minutes to see if that fixes the error. Wird geladen...